This industry standard machine offers economical flexibility, power and utility -- and does so for a very long time. The small, tight angle head can sneak a whole bunch of torque into some very small places. The head can easily be adjusted right, left, up or down giving the user a lot of options when facing a tight-place job. The balance of the machine as well as the thoughtful positioning of the controls make it seem as though your hands are fully trained in its use the first time you pick it up. The gearing and fine working right angle drive make it almost impossible to stop this durable motor. (But you can do it in a pinch - an ode to the motor design) Last year I had to change the brushes for the second time in 26 years of use. Most people get better wear than this, but in my renovation endeavors I have used this machine for everything between removing a tractor tire to a make-do winch. Other attributes: The auxillary handle is built as well as the machine itself, and is very useable. The box is standard Millwuakee tough should last through the life of the tool. If you install plumbing vents in frame houses every day, you would do better with the venerable 1676 Hole-Hawg by the same manufacturer. Otherwise strong consideration must be given to this machine as your standard 1/2" drill. Can't go wrong.

I have renovated several houses and a cabin. One of the tools I always needed was a right angle drill. I bought it and have put it to use drilling holes for electrical wiring and running pipes for plumbing. This is a powerful 1/2 inch drill which will let you drill in between studs, joists and other tight spots. I strongly recommend the Milwaukee Selfeed bits which assist in the drilling process by drawing the bit into the wood. I bought the plumbers bit kit which includes a great selection of the Selfeed bits and auger bits in a convenient carrying case. I highly reccommend these bits. The only down side to this drill is that it will wear you out if you are using it all day lifting it up overhead. This tool has tremendous torque, so make sure you have good footing and use care while drilling because this tool can literally rip itself out of your hands. But if you are using this tool, you are looking to do some serious hole drilling. You will never go back to a regular drill with a spade bit or hole saw. No wonder you will find this tool in almost every electricians and plumbers tool inventory.

The Milwaukee Right Angle Drill 3107-6 applies allot of torque to spaces you otherwise would have trouble reaching with a regular drill. It is ideal for drilling holes between studs for electric, cabling or plumbing. The unit is basically their 7 amp variable speed D handle drill featuring triple gear reduction with a Right Angle Drive (RAD) unit attached that can be set in either low gear at 355rpm or high gear at750rpm. The D handle drill without the RAD will achieve 500 RPM. Changing chuck speed from high to low or visa-versa requires removing the chuck, reversing the RAD unit and then replacing the chuck on the other side. This is fairly easy but it takes about 2-4 minutes and requires a couple of tools that are provided. The Right Angle Drive (RAD) can be easily swiveled 360 degrees providing versatility to meet any drilling angle. pUsing the drill is a pleasure as it has so much torque it just seems to eat the wood up. No standard hand drill I ever used has this kind of power. The build quality of the unit is of the highest standard and will likely last a lifetime of moderate to heavy use. This model is also fitted with Milwaukee's "quick lock" cord allowing easy replacement in the event the cord becomes damaged. pFor remodeling, basement finishing, or extensions this drill really shines. Trying to accomplish drilling many holes in wall studs with a standard electric drill would be very time consuming if not impossible for simply not being able to fit one between the studs. If however you do this kind of work every day as a business I would consider either the Hole Hawg or the new Super Hole Hawg. These units are more expensive but feature higher chuck speeds and a transmission that allows you to select the high or low speed without the use of tools. This will allow you to get work done faster when on really big jobs. But for the home owner that enjoys remodeling this Right Angle Drill is really the best choice as it is two tools in one when you consider the D-handle alone with the RAD unit removed. p Built like a tank and as much power as you could ever need this drill definately delivers. The only variable will be your choice of bits, I have to place my vote on the Milwaukee self feed bits as they cut very fast and will last a long time between sharpening. So if you have some branch circuits to run or some plumbing to install go get this drill and some self feed bits. It will make the job go much easier.

This is a great drill for making holes in tight spaces. I have gotton by over the years with a 3/8 inch electric drill and spade bits/hole saws to make all of my holes, but I dislike the spade bits because they take forever and quickly wear out, while hole saws often bottom out when cutting anything thicker than 2 by lumber. But this drill, combined with Milwaukee's and Dewalt's resharpenable self-feed bits, makes drilling holes almost effortless and I can now reach spots that I could not have before. The lower RPMs combined with the extra long side handle keep this high torque drill under control when drilling large diameter holes. I purchased a reconditioned unit for the equivalent of about 3 weeks of fees at the local rental center and it looked brand new. I have had good luck buying reconditioned gear and I tend to trust this stuff because I believe that they have been carefully examined and all the defects removed. There's no doubt that this is a specialized tool, but if you have a lot of plumbing and/or electrical work to do than it may be worth getting. It will save you a lot of time, grief, and sweat in the long run.

I just wish I had had this tool when I built our cabin. Drilling studs for electrical and plumbing with a conventional drill gives you angled holes in most cases which can be troublesome. Like my heavy duty Milwaukee hammer drill, which I did fortunately have at that time, the angle drill is obviously a durable workhorse meant for serious drilling/boring. And you can get those true right angle holes right where you want them in most cases. Add the self-feed bits and you also won't usually have to force feed or muscle it around as much. I found it indispensible when I needed to bore a 2" hole from below through a stud plate and subfloor between 12" floor joists right over a nasty concrete foundation wall. For certain jobs, its simply one of those tools you can hardly do without. I would warn anyone to think ahead and be aware you can get some terrific torque quickly if you get some bit binding while drilling so use some care or you could strain a wrist quickly..or worse if you are in an awkward position as I find myself at times. I really like this powerful tool.

If you need a 1/2 drill the versatility of this right angle drill is worth the price. The angled attachment makes if perfect for drilling between studs and other tight places. Take of the right angle attachement and it's a regular 1/2 drill.. perfect for high torque tasks like mixing motar or thin-set. This is a great tool.

Since using this, I've ditched all my spade bits and replaced them with self-feeding auger bits. This drill has the power to drive them! Changing speeds involves minor dissassembly of the chuck and right angle gearing, but its really not a big deal. I leave mine on high speed and it has handled everything I've used it for nicely.

You want power? This drill has it. Tremendous torque yet not too heavy. Comfortable grip and a very reliable brand.

We were building a house and we did quite abit ourselves, one thing was the wiring. My puny 14.4v (at the time) cordless was just way underpowered to bore through 2x's one after the other.
br /I intended to not spend much on tools, but I needed something tougher.
br /This was JUST THE TICKET.
br /It is a Power-house!
br /Now that the house is done, I don't use it as often. It has become an occasional use tool, for when the cordless drill (now 18v) won't cut it, or when the job calls for a RA drill. This tool is a very powerful drill that seems well-built.
br /I intend for it to be my heavy duty drill for many years to come.
br /

Great drill I have had several of these as well as other brands, I am pretty rough with it. The only complaint is after a couple years of use the right angle gears give out.

If you need to drill through old, full dimension oak floor joist, (very tough job) this thing will do it EASILY. Just put in a self-feeding auger bit, and away you go.
br /
br /Also, it's perfect for NORMAL jobs like holes for wiring in studs. Can't beat it. Buy it.

Not only is it a Milwaukee tool but a great tool at a great price!

I added this to my arsenal when helping a buddy build a huge deck. This thing has loads of power and could not be bogged down. Used it with the right angle head on and off. Worked perfect for tieing the deck joist to the house floor joists. With a decent auger bit, drilling even big holes was effortless. My only issue with the tool is that switching out angle head is kind of a pain.

I do not know how I did it before this tool came into my arsenal- It is a monster that makes quick work of boring holes between studs or joists to run pipes or wires. Once you use one of these with a self feed or auger bit, you will never use a standard drill with a wimpy paddle spade bit again for this purpose!